Our retail store is now open for counter service. Provincial COVID-19 guidelines apply.

Free Whitepaper: The Comprehensive Guide to Comparing 3D Filament

download Now

PT1000 Temperature Sensor up to 450C In stock

Brand: FYSETC / Triangle Labs Ships from: Canada
$15.95 CAD was Approximately:

Free Shipping within Canada and the USA on Orders >$99 CAD
Please NOTE: US orders may be subject to duties and taxes!
Local Pickup Available at our Hamilton, Ontario Store

SKU: THPT1000

Triangle Labs PT1000 Thermistor Cartridge For 3D printers.

For: Volcano, V6, Super Volcano, Mosquito, CopperHead. 

Will also fit in units that originally had a PT100 Cartridge. 3mm x 10mm

The PT100 reads Accurately up to 450C.  Great for PEEK, ULTEM, PEI printing!!!


firmware setting
Marlin:
Default 4.7Kpullup resistor please choose sensor '1047'
If you have replaced pullup with 1K resistor please choose sensor '1010'
Configuration.h:
*1047 : Pt1000 with 4k7 pullup
*1010 : Pt1000 with 1k pullup(non standard)
#define TEMP_SENSOR_0 1010
#define TEMP_SENSOR_1 0
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_BED 1
thermistortable_1010.h:
// Pt1000 with 1k0 pullup
const short temptable_1010[][2] PROGMEM = {
  PtLine(    0, 1000, 1000)
  PtLine(  25, 1000, 1000)
  PtLine(  50, 1000, 1000)
  PtLine(  75, 1000, 1000)
  PtLine(100, 1000, 1000)
  PtLine(125, 1000, 1000)
  PtLine(150, 1000, 1000)
  PtLine(175, 1000, 1000)
  PtLine(200, 1000, 1000)
  PtLine(225, 1000, 1000)
  PtLine(250, 1000, 1000)
  PtLine(275, 1000, 1000)
  PtLine(300, 1000, 1000)
  PtLine(325, 1000, 1000)
  PtLine(350, 1000, 1000)
  PtLine(375, 1000, 1000)
  PtLine(400, 1000, 1000)
  PtLine(425, 1000, 1000)
  PtLine(450, 1000, 1000)
};
thermistortable_1047.h:
// Pt1000 with 4k7 pullup
const short temptable_1047[][2] PROGMEM = {
  // only a few values are needed as the curve is very flat
  PtLine(    0, 1000, 4700)
  PtLine(  50, 1000, 4700)
  PtLine(100, 1000, 4700)
  PtLine(150, 1000, 4700)
  PtLine(200, 1000, 4700)
  PtLine(250, 1000, 4700)
  PtLine(300, 1000, 4700)
  PtLine(350, 1000, 4700)
  PtLine(400, 1000, 4700)
  PtLine(450, 1000, 4700)          
};
repetier
Pt1000 with 4k7 pullup resistor(default)
Configuration.h:
#define NUM_TEMPS_USERTHERMISTOR0 12
#define USER_THERMISTORTABLE0{{723,0},{812,320},{896,640},{975,960},{1049,1280},{1118,1600},{1184,1920},{1246,2240},{1305,2560},{1361,2880},{1414,3200},{1464,3520}}
Pt1000 with 1K pullup resistor
Configuration.h:
#define NUM_TEMPS_USERTHERMISTOR0 23
#define USER_THERMISTORTABLE0 {{2055,0},{2132,160},{2202,320},{2327,640},{2383,800},{2436,960},{2485,1120},{2531,1280},{2574,1440},{2614,1600},{2653,1760},{2689,1920},{2723,2080},{2755,2240},{2786,2400},{2815,2560},{2842,2720},{2869,2880},{2894,3040},{2918,3200},{2940,3360},{2962,3520},{2983,3680}}
You can also set up a new USER_THERMISTORTABLE in their web firmware configuration tool.
R2 is the pullup resistor of thermistor pins.
duet 3d board
M305 P1 X501 R4700;heater 1 uses a PT1000 connected to thermistor channel 1 which has a 4.7K series resistor
M305 P1 X501 R1000;heater 1 uses a PT1000 connected to thermistor channel 1 which has a 1K series resistor
smoothieware
Working on it please refer to
You can choose PT100 and amplifier board instead,if you need more than 300C temperature.Please click here
TIPS:You can use the temperature input pin P0.23-P0.26 by remove the pullup resistor of that pin.When you connect the PT100 amplifier board to your smoothieboard or MKS SBASE.(we already tested it works)
how to replace
1.Try to find any 472 or 4701 marks 'Rx' resistor near the thermistor input terminals.
2.Measure the 2pins of the terminal with a multimeter one pin should short to GND/AGND one should short to the one end of the pullup resistor
3.Replace it with your soldering iron and skills
4.Connect the PT1000 sensor like normal thermistor
5.Make the change to your firmware
6.If everything goes well the printer should show the room temperatures