Soft PLA est un autre nom pour le PLA flexible. C'est un filament d'impression 3D naturel bien qu'il ne ressemble pas exactement au PLA mais il est assez similaire et biodégradable.

Il a également une excellente adhérence entre les couches, de sorte que les impressions sont extrêmement durables. Considérez-le comme du nylon doux, car il partage quelques propriétés similaires. L'un d'eux étant que le PLA flexible a un faible coefficient de frottement.

C'est un filament polyvalent; vous pouvez l'imprimer avec une paroi épaisse ou avec plus de densité de remplissage pour une impression plus rigide et plus durable. Ou vous pouvez l'imprimer à paroi mince avec un remplissage inférieur, il est donc plus doux et flexible.

C'est un excellent matériau de départ pour que les débutants se familiarisent avec les impressions flexibles avant de passer à des matériaux avancés tels que le TPU.

La principale différence entre un filament PLA standard et flexible est une vitesse d'impression plus lente, et un lit à température plus élevée est nécessaire pour le PLA flexible.

larry s.

printed ok

Steve

Using this flexible PLA for printing a variety of gaskets with 100% infill. Pretty good durometer for this application. Cold use under 30C only though.

Michael F.

Warning: Very sticky. The instructions say to print this like PLA. That advice ripped large chunks off my PEI sheet! You're better off treating it like TPU instead, and either using a release layer or printing it on a surface which can take it. In my case, after the first mistake, I printed the rest of what I was doing directly on a bare spring steel sheet. Aside from lacking a warning about that, it's decent stuff. It's matte, flexible enough, reasonably strong and tough when printed at typical thicknesses and infill (don't go thin though), and it can be sanded relatively well.

Josiah O.

Prints are nice and I can print ridiculously fast on a stock i3. 200mm/s and I get 0 buckling. This filament is more rigid than your standard TPU and is way thinner when melted than standard TPU. It doesn't stretch much though and tends to permanently deform once bent. The layer adhesion is also quite subpar, and I found that flexing a print more like 30 times would cause the layers to split. Overhangs as expected don't print very well, but are pretty similar in quality to softer TPUs. I first tried printing at 245, but noticed it bubbled up so it seems printing at lower temps is mandatory. Could have been also moisture but I didn't have a dryer on hand.

Carl J.

superb product !

Sheldon B.

Fun stuff. I have used it to print a couple of seals for my filament holders and a wrist brace. I personally like it

Eric B.

I use it to make watches bracelets, will share soon, printing at 220c, 45mm/s, 105% flow, .2 layer, .4mm nozzle, Optional 3 walls.

Joseph K.

Use up the whole roll. Consistent size with in filament. No problems in printing whatsoever. It’s good stuff!

Brayden L.

While printing it looks great, and certain parts work well. However, the layer adhesion on thinner walls (~5mm and smaller) isn't great, causing them to split when flexing more than a couple of degrees. This is especially troublesome because it also sticks really well to my smooth build plate which causes me to need to pry prints off quite aggressively.

Sylvain C.

Printer type: Prusa I3 (Bowden tube) Temperature: Nozzle: 230C .3mm nozzle tip Bed: 30C speed: 30 mm/s (quality whould have improved with less spead. Quality was not a factor in my print) Needed to do a mod on the feeder to add bowden tube pieces on each side of the feeding wheel to stop filament to spring out of the feeder.

Marque: 3D Printing Canada / 10 Reviews

Noir - Filament PLA Flexible Standard - 1.75mm, 1kg

En stock Sale

CAD ~~CAD~~

USA Shipping: All orders ship from Canada. Duties and taxes may apply on orders over $800.

Quantité:

Inventaire actuel:

Barcode:

Quelque chose s'est mal passé !
Veuillez actualiser la page et réessayer.